The Essential Post‑Storm Roofing Safety Checklist Every Contractor Needs
When a severe storm rolls through, the rush to secure leads can tempt contractors to overlook the most critical element of any restoration project: safety. A disciplined post‑storm roofing safety checklist not only protects your crew but also preserves the integrity of the damage evidence needed for a successful insurance claim. Below is a comprehensive, field‑tested checklist that integrates crew PPE, site assessment, documentation, and compliance steps.
1. Pre‑Entry Safety Briefing
Before the first ladder touches the roof, gather the crew for a 5‑minute briefing. Cover:
- Current weather conditions (wind gusts, lightning risk).
- Identified hazards from the storm (downed power lines, loose debris, compromised structures).
- Assigned roles – who will handle PPE checks, who will document, who will manage the ladder safety.
2. Verify Crew PPE Guidelines
A post‑storm environment often contains hidden dangers. Ensure every crew member is equipped with:
- Hard hat – protects against falling branches and debris.
- Impact‑resistant safety glasses – essential when inspecting hail‑pitted shingles.
- Cut‑resistant gloves – for handling broken slate or metal flashing.
- Non‑slip, steel‑toe boots – required for wet, uneven surfaces.
- Fall protection harness – mandatory when working on roofs with a pitch greater than 6:12 or when the deck is compromised.
Tip: Use a quick PPE checklist on a tablet to confirm each item before stepping onto the roof. This reduces the chance of missed gear.
3. Conduct a Site‑Level Hazard Survey
Walk the perimeter before climbing:
- Look for downed utility lines – call the utility company and mark the area with safety cones.
- Identify standing water or ice – these create slip hazards and can mask underlying damage.
- Spot structural failures (e.g., collapsed walls, broken porch roofs) that may require a structural engineer before any roof work begins.
Document these observations with photos and notes. This documentation becomes part of the claim packet and can protect you from liability if a crew member is injured.
4. Secure the Work Zone
- Place warning signage and cone barriers around the property to keep by‑standers away.
- If the roof is wet or icy, set up temporary walkways using plywood or walk boards to provide a stable surface for ladders and crew.
- For multi‑family or commercial sites, consider cordoned off sections to limit access to areas where the roof is still being inspected.
5. Roof Inspection After Wind Damage
Once the site is secured, begin the roof inspection with a systematic approach:
- Visual sweep from the ground – note obvious missing shingles, torn underlayment, and displaced flashing.
- Close‑up inspection – use a ladder or drone to examine high‑risk zones (valleys, hips, penetrations).
- Hail damage identification – look for circular dents, granule loss, and impact bruises. Record the hail size and impact pattern; this data supports the hail‑damage claim.
- Measure affected areas – leverage the Roof Measurement App to sketch the damaged footprint, generate a square‑footage estimate, and attach photos directly to the job file.
6. Insurance Adjuster Site‑Visit Protocol
If an adjuster is scheduled to visit, coordinate with them to ensure a smooth process:
- Provide a pre‑inspection packet that includes your safety survey, hazard mitigation steps, and preliminary measurements.
- Assign a crew lead to walk the adjuster through the site, pointing out repaired or compromised areas while wearing appropriate PPE.
- Answer questions transparently – explain any safety measures taken (e.g., why a section was cordoned off) to demonstrate professionalism and risk awareness.
7. Document, Document, Document
Every step of the checklist should be captured in the project’s digital record:
- Photos with timestamps – use a smartphone or camera with GPS tagging.
- Video walkthroughs – especially useful for large commercial roofs where a single photo may not convey the full scope.
- Annotated sketches – the Roof Measurement App allows you to overlay damage notes directly on the roof diagram.
- Safety logs – record PPE checks, hazard surveys, and any incidents (even near‑misses) in the CRM for future reference.
These records form the backbone of the claim packet and can be referenced during insurance adjuster site visits or supplement claim negotiations.
8. Post‑Inspection Clean‑Up and Hazard Mitigation
After the inspection:
- Remove all cones, signs, and temporary walkways to restore the property to a safe condition for the homeowner.
- Secure loose debris that could cause future injuries – this also shows the homeowner you’re protecting their property beyond the immediate repair.
- Update the storm canvassing app with the final lead status (e.g., "Inspection Complete – Ready for Estimate"). This keeps the pipeline accurate and helps prioritize follow‑up calls.
9. Review and Debrief
Hold a brief post‑job meeting to:
- Discuss any safety incidents or near‑misses.
- Evaluate the effectiveness of the checklist – adjust steps as needed for future storms.
- Confirm that all documentation is uploaded to the CRM and that the estimate workflow can begin.
Frequently asked questions
How often should I update my post‑storm safety checklist?
Review it after each major storm season or whenever new safety regulations are released. Incorporate crew feedback to keep it practical.
What if I discover structural damage during the inspection?
Stop work immediately, document the finding, and consult a licensed structural engineer. Proceed only after a written assessment clears the roof for safe entry.
Can I use the same checklist for hail and wind events?
Yes, but add hail‑specific items such as granule loss assessment and hail‑size estimation. The core safety steps remain identical.
How does proper documentation affect my insurance claim?
Accurate, timestamped photos and measured footprints create a defensible claim packet, reducing the likelihood of claim denial or lowball offers.
What PPE is mandatory for roof work after a storm?
Hard hat, safety glasses, cut‑resistant gloves, non‑slip steel‑toe boots, and fall protection harness for any work above 6:12 pitch or on compromised decks.
See WeatherOps on your next storm
Storm map, property intel, measurements, estimates, and the claim — in one workflow.